Industry
Fact-checked

At AboutMechanics, we're committed to delivering accurate, trustworthy information. Our expert-authored content is rigorously fact-checked and sourced from credible authorities. Discover how we uphold the highest standards in providing you with reliable knowledge.

Learn more...

What is a Forming Limit Diagram?

H.R. Childress
H.R. Childress

A forming limit diagram (FLD), also known as a Keeler-Goodwin diagram, is a graph that illustrates the behavior of sheet metal under different levels of strain. The line describing the behavior of the metal is called a forming limit curve (FLC). A forming limit diagram provides information on the maximum stress the metal can undergo before fracturing or necking. The diagrams are constructed by using test strips of sheet metal and measuring the deformation.

Forming limit diagrams are graphed in a two-dimensional coordinate system, with the major strain plotted on the y-axis and the minor strain plotted on the x-axis. Strain is a measure of the deformation — major strain is defined as being in the direction with higher deformation, while minor strain is in the direction with less deformation. Different types and different thicknesses of sheet metal each have their own unique forming limit diagram.

A forming limit diagram shows the behavior of sheet metal under different conditions.
A forming limit diagram shows the behavior of sheet metal under different conditions.

An FLC is an irregular parabolic curve, with the minimum occurring at or near the major strain axis. A material subjected to strains that lie above the curve will fail, while strains below the curve are safe to apply to the metal. FLDs are usually graphed with two curves — the area between the curves is a zone of critical deformation or safety zone, where the material may be safe or may crack, so in practice it is best not to apply those strains. The critical deformation that is likely to occur in this zone is called necking, which is when the metal is stretched thinner in some areas.

A forming limit diagram is developed using a series of tests. During the tests, strains are applied to metal strips of differing widths. The different widths of strips simulate different strain conditions. Each strip is marked with a circular grid pattern that is used to measure the strain.

Strain is usually applied to the strips using a hemispherical punch. A metal strip is stretched until necking is observed. Strain values for the major and minor axes can be obtained by measuring the deformation of the circular grid previously marked on the strip.

Computer-based methods may also be used for measuring strain. Images taken by the computer during the deformation process can be compared to a reference grid comparable to the circular grid on the metal. The computer can compute the strains using these images. Another method compares before and after images of the circular grid in order to calculate strain.

Discussion Comments

everetra

@Charred - I can’t speak to the science behind the steel collapses in the terrorist attacks. I do know that metal fabricators use a variety of metal forming techniques to shape the steel into a particular shape.

From what I understand some of these methods use cold as part of the process while others use heat. I don’t know how much heat is applied using the heat techniques, but I assume that during this process they have an acceptable threshold for how much heat the metal can endure.

Again, whether the steel can withstand more than that or whether the fires of September 11,2001 were much hotter than that threshold, I cannot stay. But the metal fabricators do run their tests through a variety of what-if scenarios as I understand it.

Charred

I think that the forming limit diagram is useful for determining how much strain sheet metal can take, but of course custom metal fabrication cannot take into account all possible variables in advance.

For example, they may want to make steel to use in building construction. They have to anticipate how much weight is put on the metal through normal usage. But what if something spectacular happens that puts undue strain on the steel?

After the September 11,2001 attacks for example, there was considerable speculation as to why the buildings fell given the tensile strength of the steel.

Some said the metal should have stood up under the strain of the two airplanes, while others argued otherwise. Detractors became conspiracy theorists as a result.

From my understanding, it was the heat of the airplanes and not just their weight that caused the building to collapse. No one could have anticipated this.

Post your comments
Login:
Forgot password?
Register:
    • A forming limit diagram shows the behavior of sheet metal under different conditions.
      By: Kybele
      A forming limit diagram shows the behavior of sheet metal under different conditions.